Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Blog Article
Are you interested in tips about How to Install a Bathtub?
Mounting a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging project. If the old tub is easily obtainable, the project can move rapidly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the brand-new one. Make certain you have actually certified on your own for the work and also fit trying it. Rather than hiring a professional to take over a halfway-completed project, it is much better to think about employing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have currently gotten a brand-new bathtub as well as don't require to transform the setup of your previous water pipelines.
Your devices as well as material checklist ought to consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bath tub till the spirit level checks out degree.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bathtub as well as also check the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will certainly resolve it into its final placement.
Preparing for the Setup
First of all, the sustaining framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to pass through the wall between the bathroom and the tiling, bring about issues with dampness and also feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the bath tub with water before securing, to allow for the activity experienced when the tub is in use. The sealant can crack rather early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that page on How to Install a Bathtub Yourself when doing a lookup on the web. Sharing is nice. You never know, you may be doing someone a favor. Kudos for your time. Visit again soon.
Appointment
Report this page